Flirc raspberry pi 3 case install12/12/2023 My reasoning for wanting to do this is not energy/money based, but rather making a set top box that could be powered on, much like a cable box, DVD player, cable box etc. Thank you for linking some of the power management boards. Would this not be enough to get the Flirc to be able to reset the pi? (I'm assuming not, from your post, but curious as to what is lacking or needed to make this work theoretically) Well instead of plugging directly into the pi, I plugged it into a micro usb y cable that has a male plug on the other side going to the Pi, and the 3rd side is a USB port (so power is coming from a source outside of the pi) so I have the flirc powered, independently of the raspberry pi, as well as connected to a usb port on the pi. Just past the power switch, there is a micro usb cable that plugs into the pi. The adapter cables that I added to the media pi case accomplishes the part where you said "The hardware should have its own power supply port (which should be used to power whole set instead of RPi's Micro USB one)". My though is (and my thoughts very well may be wrong) If I could get the RUN pins to connect, this would cause the PI to reset, and reload the operating system, essentially "booting" the pi, but as stated before, "boot" is not really the correct term. Also, you said there isn't a power button, but there is a place to put a reset switch (it's labeled as RUN on the board). I suppose "Boot" is a loaded and incorrect word in this sense, I should have said "wake" or "bring out of hibernation" or something to that effect. Of course the cost is also dependent on the cost of electricity in your area (mine is around $0.13 per kWh). I've been doing some calculations on the power consumption and cost when RPi 3 is running constantly and it was only a few dollars per year (I don't remember exactly how much, the calculation is somewhere on the forum). I don't have any of them as there's really no need to do that. I don't know if these boards can be adapted to properly work with Flirc SE though. There are some extension boards which add power management functionality to RPi. This is not enough for properly interfacing RPi with Flirc SE (actually it doesn't add anything helpful in this topic). It looks like it connects the external power supply port directly to RPi, with just a simple hardware power switch in between. I've read the manual for MEDIAPI+ and the board inside of it doesn't support any of the requirements I've described. The hardware should support power button by itself. It would also probably need additional software running on the Pi which would communicate with extra hardware over GPIO (for example to notify it that the OS has been properly closed and the power can be cut). The hardware should have its own power supply port (which should be used to power whole set instead of RPi's Micro USB one) and probably should also connect to RPi's GPIO pins. To actually use Flirc SE with RPi you'd need additional hardware. There's also no power button support on the board, so it's not directly compatible with Flirc SE - as RPi doesn't support power states you can't control them with Flirc SE. So as long as you have power connected directly to the RPi it will draw it no matter if the OS is running or not. Sorry for the rather noobish question, I am trying to teach myself this stuff as much as possible, I have searched first, and did not see anything that covered this, so if it is covered elsewhere, could you please direct me to it? thanks in advance for any information or guidance anyone is able to give.įirst of all, Raspberry Pi (any version that is available up to this date) does not have any power management by itself at all. So I bought a flirc SE, and I have a couple adapter cables plugged in that allowed me to have the flirc se powered off of the incoming power, and it also splits to power raspbery pi (internal usb cable that came with FLIRC SE going to adapter cable that gives me standard usb plug, going into female usb plug that splits into 1 male, 1 female micro usb) so I have power going to everything, My question is, how do I set the IR remote to "boot" or wake from sleep or wake from hibernate?Īlso, I am assuming I will need to connect one of the power switch pin pairs up to the raspberry pi for the actual boot command to work, Can I connect it to the run pin holes as that does a reset? I have a media pi+ case ( or ) I am not using the onboard IR that came with it, as there's no power to it when the raspberry pi shutsdown. First, I want to say, I have covered the issue of no power to the flirc to be able to boot.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |